
Toilet Installation in Richmond, VA
Old toilet out, new toilet in, seated level and checked for leaks. We replace toilets in homes across Richmond and Henrico County.
Replacing a Toilet the Right Way
A toilet looks like a simple fixture, but installing one properly depends on a few unforgiving details: the height of the flange, the seal between the toilet and the drain and the flatness of the floor underneath. Get any of them wrong and the toilet rocks, the seal fails or a slow leak ends up rotting the floor beneath.
The job is more than lifting one toilet out and putting another in. We shut off and disconnect the water, remove the old toilet, clean and inspect the flange and the floor, set a new seal, seat the toilet level and connect new supply lines. Then we check the fill, flush and connections for leaks before we leave.
Toilet replacement is often a chance to update a bathroom a little at a time. In older Richmond homes, floor and flange conditions can vary room to room, so a toilet swap is a good moment to catch soft subfloor or corroded hardware before it becomes a bigger problem. For larger updates see bathroom remodeling.
Signs You Need a New Toilet
Toilets last a long time, but these are the signs that it is time:
- A crack in the bowl or tank, even a hairline one, which can turn into a leak.
- Frequent clogs or a weak flush that do not improve after cleaning or new parts.
- A toilet that rocks or leaks at the base, which can mean a failing seal or flange.
- High water use, since older toilets often use far more water per flush than modern models.
- Stains and wear that no longer come clean, or a bathroom update that calls for a new look.
How We Install a Toilet
Confirm the fit
We check the rough-in distance, the bowl shape and the space around the toilet to be sure the new model fits.
Remove the old toilet
We shut off the water, drain the tank, disconnect the supply line and lift the toilet off its seal.
Inspect and prepare the flange
We clean the area, check the flange for damage and height and make sure the floor around it is solid and flat.
Set the new toilet
We fit a new wax ring or seal, lower the toilet into place, tighten the bolts evenly and level it.
Connect and test
We install a new supply line, turn the water on, set the tank and flush several times while checking all connections for leaks.
What Changes the Price of Toilet Installation
A toilet swap is one of the quicker jobs we do, and these are the factors that affect its cost:
The toilet itself
Basic, comfort-height, wall-hung and smart toilets span a wide range of prices.
Condition of the flange and floor
A damaged flange or soft floor adds repair work that cannot be skipped.
Supply line and shutoff valve
An old or stuck shutoff valve may need replacing to do the job safely.
Removal and disposal
Hauling away the old toilet is part of many jobs, and large or heavy fixtures take more effort.
Access
Tight spaces, basement bathrooms and second-floor bathrooms affect setup and handling.
Extras
Bidets, new seats and nearby trim or caulking work add small amounts of time.
Why Richmond Homeowners Choose EGM Renovations for Toilet Installation
Toilet installation is one of the bathroom jobs Edwin Madrigal does. He treats it as a seal-and-level job, not a swap, and the work is not finished until the new toilet has been flushed and checked for leaks.
Because we also tile and paint, we can fix what the old toilet leaves behind: a stained floor patch, missing caulk or a wall that needs a touch-up. That keeps the bathroom from looking half-finished.
You get a direct answer on what is involved and a free quote. If your bathroom needs more than a toilet, our tile installation page shows what else we can do.
Toilet Installation FAQs
How do I know if I need a new toilet or just a repair?
If the toilet is cracked, constantly clogs, runs even after new internal parts or uses a lot of water, replacing it usually makes more sense. Simple problems like a worn flapper or a loose handle are repairs. We can tell you which you have when we see it.
What is the "rough-in" and why does it matter?
The rough-in is the distance from the wall to the center of the drain, commonly 12 inches. A toilet must match it or it will not fit properly. Measure before you buy, or ask us to measure for you.
Why does my toilet rock a little?
It is usually a floor that is not perfectly flat, loose closet bolts or a flange that sits too high or too low. A rocking toilet can break its wax seal and leak, so it should be fixed, not ignored.
Do I need a new wax ring every time?
Yes. A wax ring is a one-use seal, and reusing it risks a leak under the floor that may not show for weeks. Replacing the ring is a standard part of setting a toilet.
Can you install a toilet I bought myself?
Yes. Check the rough-in and the shape of the bowl against the space first, and ask us before you buy if you can. We will use new supply lines and a new seal as part of the job.



